Dating fender bassman silverface
These dampers are NOT for 9-pin power tubes, such as the EL84 or 6BQ5. Princeton and Princeton Reverb do not need the resistors. Do not install in an amplifier that does not have a standby switch - always use the standby switch in amps so equipped when using the 5SSR.
This is a great kit to replaced all 6 of the tube shields in many Fender amps with 6 preamp tubes. Note: Tube shields will not fit over the damper rings, and must be removed from the tubes. Contains two 8-pin sockets, two "bear trap" retainers, four mounting screws, two 470 ohm screen grid resistors (Metal-Film Flameproof for safety), and two carbon composition 1500 ohm control grid resistors. 1.31" diameter, 0.89" tall (not including pins and center post).necessary that a standby switch is used in conjunction with this device.
Includes 4 bolts and 4 matching nuts with integral lock washers. Pack of 6 stainless steel back panel screws for Fender original and reissue "Tweed" series amps. Mounts the chassis to the cabinet on top as well as the sides of the cabinet. Mounts the chassis to the cabinet on top as well as the sides of the cabinet. Set of 4 screws, stainless steel, 1 1/4 inches long, Phillips, oval head.
This set of four screws fits either the top or bottom rear panels on Fender combo amps from the 60s and 70s, and todays reissues of those BF and SF May be used with the BCW-10 cup washers.
See data sheet BACK PANEL STAINLESS STEEL SCREWS (SET OF 8) FOR OPEN BACK CABINETS (such as Fender Blonde, Brown, Blackface and Silverface Series).
Set of 6 screws with oval Philips heads, stainless steel #8, 1 1/2 inches long, and matching set of 6 stainless steel cup washers.
This set of six screws w/washers fastens the speaker baffle board to the cabinet on Fender blonde, brownface, blackface and silverface combo amps from the 60s and 70s, and todays reissues of those BF and SF amps. SPEAKER BAFFLE MOUNTING COPPER SCREWS AND STAINLESS STEEL KEPS NUTS (SET OF 4) FOR Fender TWEED AMPS.
Used on the upper left corner of the grill cloth on most CBS era Fender amps. 4 1/2" wide, the "F" in the logo is about 2 1/2" inches tall. "Flat" Fender logo, with black "tail", cast metal, mounting screws included. New original Fender reproduction, used in many recent and current model Fenders.
Used on the upper left corner of the grill cloth on some recent and vintage era Fender amps. 5 1/2" wide, the "F" in the logo is about 2 7/8" inches tall. "Flat" Fender logo, with brown "tail", cast metal, mounting screws included.
Perfect for Twin Reverb, Showman and Dual Showman, Quad Reverb, Bassman 100, etc. Founded in 1948 by Heinz Fischer and Alfred Tausche, F&T Capacitors has over 60 years of experience in producing some of the finest capacitors available today.
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL, SET OF 6. Contains four 8-pin sockets, four "bear trap" retainers, eight mounting screws, four 470 ohm screen grid resistors (Metal-Film Flameproof for safety), and four carbon composition 1500 ohm control grid resistors. CAPACITOR, F&T BRAND, AXIAL LEAD ELECTROLYTIC, VARIOUS VALUES AND VOLTAGES AVAILABLE (SEE OPTIONS) Made in Germany.
Set of 8 screws, satin black stainless steel, 1 1/4 inches long, Phillips, oval head.
Set of 8 completely replaces all of the screws on the two back panels. See data sheet SPEAKER BAFFLE MOUNTING STAINLESS STEEL SCREWS AND WASHERS (SET OF 6) FOR Fender Blackface and Silverface Series.
Set of 6 rings - will equip either 2 or 3 tubes, depending on the number of rings you choose for each tube. Fender Vintage Amp (60s Blackface and 70s Silverface) Power Tube Socket replacement kit. ) from the original blackface and silverface eras which have two power tubes (6L6 or 6V6).Tags: Adult Dating, affair dating, sex dating